Tips on the use of automatic feeding mixer

搅拌车在出现故障的时候，需要及时将内部的混凝土清理出来，通常有两种方法清理：

When the mixer truck breaks down, it is necessary to clean the internal concrete in time. There are usually two methods to clean it:

方法一：

Method 1:

1.准备好紧急驱动软管，将搅拌车熄火，卸下液压马达上的高压油管接头。

1. Prepare the emergency drive hose, turn off the mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.

2.将救援车熄火，将其液压马达的高压油管卸下，并与故障车上的对应接头用紧急驱动软管相连。

2. Turn off the rescue vehicle, remove the high-pressure oil pipe of its hydraulic motor and connect it with the corresponding connector on the faulty vehicle with emergency drive hose.

3.发动救援车，将其操纵手柄拨出料位置，故障车内的混凝土即被排出。

3. Start the rescue vehicle, turn its control handle to the discharge position, and the concrete in the faulty vehicle will be discharged.

4.紧急驱动完毕后，将驱动软管卸下，并恢复两车原状。

4. After the emergency drive, remove the drive hose and restore the two vehicles to their original state.

方法二：

Method 2:

在托轮和滚道之间放入木楔，以控制搅拌筒的旋转，一定要注意身体；将发动机熄火，拆松液压马达的一根高压油管，搅拌筒可自由旋转，控制搅拌筒的旋转，使维修孔转到下部，然后打开维修孔，清理出筒内混凝土。混凝土排出完毕后，恢复搅拌车原状。在一般情况下，多数人会选择用方法一来，当方法一不了时才会选择方法二。

Put a wooden wedge between the supporting wheel and the raceway to control the rotation of the mixing drum. Be sure to pay attention to your body; Turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, the mixing drum can rotate freely, control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then open the maintenance hole to clean the concrete in the drum. After the concrete is discharged, the mixer truck shall be restored to its original state. In general, most people will choose method one to solve it, and only choose method two when method one can't solve it.

特别是灌桩发热：

In particular, cast-in-place pile heating:

1.油泵吸油口的过滤网是否堵塞了，拆出滤网清洗一下，再试试追问刚换的柱塞 泵和马达全大修的。

1. Check whether the filter screen at the oil suction port of the oil pump is blocked, remove the filter screen and clean it, and then try to ask about the overhaul of the plunger pump and motor just replaced.

2.在装管的时候，密封性是有没有装好，有没有可能漏气 。

2. When installing the pipe, whether the sealing is well installed and whether there is possible air leakage.

3.检测压力是否正常 。

3. Check whether the pressure is normal.

4.检查连轴器是否出现发热。以上是自动上料搅拌车的相关知识，欢迎大家多多关注我们的网站！

4. Check whether the coupling is heated. The above is the relevant knowledge of automatic loading mixer. Welcome to pay more attention to our website!

本文由 江南体育下载地址为您提供，我们的网站是： //www.scritchies.com/我们将以全心全意的热为您提供服务，欢迎您的访问

This article is provided for you by the automatic self loading mixer. Our website is: //www.scritchies.com/ We will serve you wholeheartedly. Welcome to visit