自动上料搅拌车的正确操作方法的“六步归纳”
"Six step induction" of correct operation method of automatic feeding mixer
自动上料搅拌车柔性正确操作方法可以归纳为：一轻、二稳、三离、四勤、五协调、六严禁。
The correct flexible operation methods of the automatic feeding mixer can be summarized as follows: one light, two stable, three separated, four diligent, five coordinated and six forbidden.
自动上料搅拌车的正确操作方法的“六步归纳”
"Six step induction" of correct operation method of automatic feeding mixer
一轻：
One light:
在自动上料搅拌车作业时脚跟紧抵驾驶室地板，脚板和油门踏板保持平行，轻缓地下压加油踏板。
During the operation of the automatic feeding mixer, the heel is firmly against the cab floor, the foot plate is parallel to the accelerator pedal, and gently press the refueling pedal.
二稳：
Bistable:
自动上料搅拌车在作业中，油门始终要稳住。一般作业状态下，油门开度在70%左右为宜。
During the operation of the automatic feeding mixer, the accelerator should always be stable. In general operation state, the throttle opening should be about 70%.
三离：
Three Departures:
在自动上料搅拌车作业时，脚板应和制动踏板分离开，平放到驾驶室地板上，决不能踩在制动踏板上。自动上料搅拌车常常在凹凸不平的工地作业，如果脚总是踩在制动踏板上，机身上下窜动会造成驾驶员不轻意地踩制动踏板。一般情况下，要用控制油门减速的办法控制机况和换挡。这样既避免了频繁制动造成制动系统过热，又为自动上料搅拌车快捷的提速带来方便。
During the operation of the automatic feeding mixer, the foot plate shall be separated from the brake pedal and placed flat on the cab floor. Never step on the brake pedal. The automatic feeding mixer often works on uneven construction sites. If the foot always steps on the brake pedal, the body will move up and down, causing the driver to step on the brake pedal carelessly. In general, the engine condition and gear shifting shall be controlled by controlling the throttle deceleration. This not only avoids overheating of the braking system caused by frequent braking, but also brings convenience for fast speed increase of the automatic feeding mixer.
自动上料搅拌车的正确操作方法的“六步归纳”
"Six step induction" of correct operation method of automatic feeding mixer
四勤：
Four attendance:
在自动上料搅拌车作业时，特别是在铲挖作业时，应在油门稳定情况下，用循环扳动起升和转斗操纵杆的方法使铲斗铲满物料。起升和转斗操纵杠的循环扳动就是所说的“勤”。这个过程非常重要，对耗油量的影响很大。
During the operation of the automatic feeding mixer, especially the shoveling operation, the bucket shall be filled with materials by cyclically pulling the lifting and bucket turning control levers under the condition of stable accelerator. The cyclic pulling of the lifting and bucket turning control levers is called "diligence". This process is very important and has a great impact on fuel consumption.

五协调：
V. Coordination:
协调就是起升和转斗操纵杠有机的配合。自动上料搅拌车一般的铲挖过程是将铲斗平放在地面，平稳地驶向料堆。在铲斗平行铲往料堆遇阻力时，应遵循先起臂后收斗的原则。这样可更好地避免铲斗底部受到阻力，从而能够充分发挥更大的掘起力。
Coordination is the organic cooperation between the lifting and bucket control rods. The general shovel digging process of the automatic loading mixer is to place the bucket flat on the ground and drive steadily to the material pile. When the bucket is parallel to the material pile and encounters resistance, the principle of lifting the boom first and then retracting the bucket shall be followed. In this way, the bucket bottom can be better protected from resistance, so that greater digging force can be fully exerted.
自动上料搅拌车的正确操作方法的“六步归纳”
"Six step induction" of correct operation method of automatic feeding mixer
六严禁：
VI. Prohibitions:
是严禁轮胎打滑。自动上料搅拌车作业时，遇阻力而猛加油门往往会出现轮胎打滑的现象。这种现象通常是由于驾驶员操作不当造成的，既增加了油耗又损伤了轮胎。
First of all, it is forbidden to slip the tires. During the operation of the automatic feeding mixer, when encountering resistance, the fuel valve will often slip. This phenomenon is usually caused by the driver's improper operation, which increases fuel consumption and damages the tire.
其次是严禁后轮翘起。由于自动上料搅拌车的掘起力大，驾驶员通常在铲挖坚实的原土和石料山等作业过程中，如果操作不当就容易出现两后轮翘起离地现象。这种翘起动作的落地惯性，会造成铲斗的刃板断裂、铲斗变形；后轮翘起很高时还容易引起前后机架等结构的焊接处开裂，甚板材断裂等。
Secondly, it is forbidden to tilt the rear wheel. Due to the large digging force of the automatic feeding mixer, the driver is usually prone to the phenomenon of two rear wheels tilting off the ground if he/she does not operate properly in the process of digging solid original soil and stone hill. The landing inertia of the lifting action will cause the blade of the bucket to break and the bucket to deform; When the rear wheel is cocked up very high, it is also easy to cause cracks at the welding points of the front and rear frames and other structures, or even plate fractures.
第三是严禁撞击料堆。铲挖普通物料，自动上料搅拌车可以用II档作业，严禁以II档以上的档位向料堆进行惯性冲击。正确的方法应该是铲斗在接近料堆时适时地把档位转换为I档完成一个铲料过程。
Third, it is strictly prohibited to impact the material pile. For shoveling and digging ordinary materials, the automatic feeding mixer can operate with gear II. Inertial impact to the material pile with gear above gear II is strictly prohibited. The correct method should be to change the gear to gear I timely when the bucket is approaching the pile to complete a shoveling process.